Renogy Rover 2 Pro MPPT Solar Charge Controller with Bluetooth and Display
Solar power for greater independence – with your leisure battery charging status always in view: The Renogy Rover 2 Pro connects your solar panels to your 12V or 24V electrical system, efficiently converting available solar energy into charging power. Whether you use a LiFePO4, AGM, gel or conventional flooded lead-acid battery, you can configure the controller to suit your battery and monitor operation on the built-in display or through the Renogy App.
This MPPT solar charge controller is suitable for both new camper van conversions and upgrades to existing motorhome solar installations.
Your benefits at a glance
- Efficient MPPT technology: Adjusts the solar panels’ operating point as conditions change to make the most of the available power.
- For 12V and 24V systems: Automatic voltage detection for supported lead-acid batteries and manual selection for LiFePO4.
- Compatible with various battery types: Supports LiFePO4, AGM, gel and flooded lead-acid batteries, as well as custom battery settings.
- Built-in display: Check operating status, charging stage and parameters without a smartphone.
- Bluetooth and app control: Monitor controller data, adjust settings and access fault alerts through the Renogy App.
- Switchable load output: Connect and switch compatible DC appliances drawing up to 20A in total.
- Temperature sensor included: Enables temperature compensation of the float charging voltage for lead-acid batteries.
Make the most of solar power as conditions change
Solar panel output varies with sunlight intensity and panel temperature. The Rover 2 Pro uses Maximum Power Point Tracking, or MPPT, to adjust the panels’ operating point to these conditions. It converts the harvested solar energy to the charging voltage required by your leisure battery.
This helps your solar installation offset daily electricity consumption and supports longer stays without a mains hook-up. The energy available will depend on factors such as panel area, weather, orientation and shading.
Configurable for LiFePO4 and lead-acid batteries
The Rover 2 Pro supports lithium iron phosphate batteries, as well as AGM, gel and flooded lead-acid batteries. Select the appropriate battery type directly on the controller. In user-defined mode, you can customise battery parameters through the Renogy App to match your battery’s charging requirements.
For supported lead-acid batteries, the controller automatically detects whether it is connected to a 12V or 24V system. For LiFePO4 batteries, you must select the system voltage manually. Configure the correct battery type before first use; the factory default is flooded lead-acid.
The included temperature sensor is intended for lead-acid batteries. It must not be used with LiFePO4 batteries equipped with a battery management system.
Monitor on the display or through the app
The built-in LCD and four control buttons let you check operation and make basic adjustments directly on the controller. Displayed information includes charging stage, system voltage, battery type and operating status.
Connect the Rover 2 Pro to the Renogy App via Bluetooth to monitor and adjust controller parameters and access fault alerts. For a reliable connection, keep your smartphone within approximately three metres of the controller.
Remote monitoring over the internet is possible with an additional Renogy ONE Core and an internet connection. The ONE Core is sold separately.
Additional output for DC appliances
The dedicated load output allows you to connect compatible DC appliances with a combined current draw of up to 20A. In manual mode, you can switch this output on and off using a button on the controller.
The output voltage depends on the battery voltage, so connected appliances must be suitable for the respective 12V or 24V electrical system. The load output is rated for a maximum of 20A on all versions, regardless of the controller’s charging current rating.
Choose the right version for your solar installation
When selecting your controller, consider not only its maximum charging current but also the permitted solar input power, open-circuit voltage and short-circuit current of your solar array. The relevant limits are listed in the technical specifications for each version.
Install the Rover 2 Pro in a dry, well-ventilated location inside the vehicle, preferably vertically with the terminals facing downwards. During installation, connect the battery first, followed by the solar array.
Specifications by version
| Specification | 20A | 30A | 40A | 50A |
|---|---|---|---|---|
| Model number | RCC-M10020-B2 | RCC-M10030-B2 | RCC-M10040-B2 | RCC-M10050-B2 |
| Rated charging current | 20A | 30A | 40A | 50A |
| Maximum solar input power at 12V | 300W | 450W | 600W | 750W |
| Maximum solar input power at 24V | 600W | 900W | 1,200W | 1,500W |
| Maximum permitted PV short-circuit current | 20A | 30A | 40A | 50A |
| Dimensions | 162 × 108 × 57 mm | 162 × 108 × 62 mm | 180 × 132 × 71 mm | 180 × 132 × 81 mm |
Specifications common to all versions
| Specification | All four versions |
|---|---|
| System voltage | 12V / 24V |
| Battery types | LiFePO4, AGM, sealed lead-acid (SLD), gel, flooded lead-acid (FLD) |
| Custom battery parameters | Via USE mode and the Renogy App |
| PV open-circuit voltage (Voc) | 15–100V |
| Maximum load output current | 20A |
| Load output voltage | Depends on battery voltage |
| Display and controls | LCD with four buttons |
| Wireless communication | Bluetooth / Renogy App |
| Communication ports | CAN/RS485 |
| Maximum terminal cable cross-section | 13.30 mm² (6 AWG) |
| Operating temperature | −30 to +65 °C; power derating above +45 °C |
| Installation location | Dry, ventilated indoor location |
manufacturer information:
RNG Germany GmbH
Am Maibusch 108
Gelsenkirchen, 45883
Nordrhein-Westfalen, DE
supportde@renogy.com
responsible person:
RNG Germany GmbH
Am Maibusch 108
Gelsenkirchen, 45883
Nordrhein-Westfalen, DE
supportde@renogy.com
There are no reviews yet.