Skip to main content Skip to search Skip to navigation

Installation Materials

Matching connections for the water system in your camper van or motorhome: here you’ll find hoses, hose tails, connectors, tank fittings and clamps. Choose components according to their intended ...
more Read

Installation Materials

Matching connections for the water system in your camper van or motorhome: here you’ll find hoses, hose tails, connectors, tank fittings and clamps. Choose components according to their intended use, connection sizes, and temperature and pressure ratings. This helps everything fit together, from the tank filling hose to the hot water line.

Which installation materials do you need for your water system?

A simple sketch helps you put your system together: where will the tank, pump, filter, water heater and outlets be located? Which connections do these components have, and where do you need branches or changes of direction? Mark the connection sizes directly on your plan. You can then select hose lengths, fittings and clamps accordingly.

Choose hoses to suit the fluid, temperature and pressure

Drinking water lines, tank filling hoses, wastewater lines and coolant circuits place different demands on the materials. Choose a hose specifically suited to its intended use. The right diameter alone is not enough.

For drinking water installations, our range includes red and blue hoses with a 10 mm internal diameter. The colours help distinguish hot and cold water lines, but they don’t replace a check of the specifications: always confirm the permitted temperature and operating pressure.

Temperatures directly at the water heater can be higher than at the outlet. For these connections, we offer highly heat-resistant silicone drinking water hoses. The connected fittings must also withstand the temperatures at that point in the system. For tank filling and wastewater, suitable spiral-reinforced hoses are available.

Understanding internal diameter, external diameter and thread types

For hose connections, descriptions such as “LW 10” or “for 10 mm hose” generally refer to the hose’s internal diameter. When choosing a clamp, however, the external diameter at the assembled connection is what matters. Two hoses with the same internal diameter may need different clamps because their wall thicknesses differ.

An example from our range: the silicone hose with a 10 mm internal diameter has an 18 mm external diameter. A clamp intended for a thinner-walled 10 mm hose will therefore not necessarily fit. Check the clamp’s adjustment range and suitability for the hose you’re using.

For threaded fittings, check the full specification. A G 1/2 connection and a 1/2-inch NPT connection are different despite their similar size designation. The thread type, size and male or female connection must match. The required sealing method also depends on the specific fitting.

Straight connector, elbow or branch?

Straight connectors join two sections of hose, elbows allow changes of direction, and T- or Y-pieces distribute water into several lines. Choose the fitting according to your hose routing and available space. A suitable elbow can, for example, prevent a hose from bending too tightly behind a pump or underneath a sink.

Check the connections on pumps, filters and water heaters before ordering adapters. Even within one water system, different thread types and hose diameters may be used. Components designed for a coolant circuit are also not automatically suitable for a drinking water installation.

Plan clamps and hose routing together

The clamp must suit the hose material, connection shape and required clamping range. A spiral-reinforced hose may need a different clamp from a smooth drinking water hose. Overtightening cannot compensate for a clamp that is too large or unsuitable.

Route hoses without kinks, tension or rubbing points. Keep connections accessible wherever possible and consider how you’ll drain the system later. After installation, check every connection for leaks under the intended operating conditions – including after heating up any hot water lines.

Quick checks before ordering

  • Intended use: Drinking water, hot water, tank filling, wastewater or coolant?
  • Dimensions: Do the hose’s internal diameter, fitting size and clamp adjustment range match?
  • Threads: Are the thread type, size and connection configuration compatible?
  • Ratings: Are all components suitable for the temperatures and pressures they will encounter?
  • Included parts: Which connections and mounting components already come with your equipment or kits?